To customize the behavior of the Boot Agent software in a pre-boot, PXE or RPL environment: Press Ctrl+S immediately after the initialization message appears. A configuration setup menu appears allowing you to set configuration values for the Boot Agent.
Full Answer
How do I configure the boot agent software in a DOS environment?
You can use the IBACFG.EXE program to configure the Boot Agent software in a DOS environment. This executable provides a more user-friendly method for configuring Boot Agent images than does IBAUtil. IBACFG controls the same settings as those offered on the configuration setup menu when you press Ctrl+Safter POSTfor PXE implementations.
How do I set Boot agent configuration values?
A configuration setup menu appears allowing you to set configuration values for the Boot Agent. The configuration setup menu is the same for both kinds of adapters and looks similar to the screen image below.
How do I configure the Intel® Boot agent software?
The Intel® Boot Agent software provides configuration options that allow you to customize the behavior of the Boot Agent software. You can configure the Boot Agent in any of the following environments: A pre-boot environment (before operating system is loaded) A Windows environment A DOS environment
Why did I receive a warning message when configuring the boot agent?
CAUTION: If you attempt to configure the Boot Agent in a DOS environment where the boot source is a LOM or a NIC without flash ROM, you will receive a warning message. This message indicates that any configuration settings you've changed may not take effect if you do not have the Boot Agent image built into the system BIOS.
How do I enable Intel boot agent?
Intel Boot Agent (IBA) initializes during the system startup, even if it isn't the first boot device. Once the initialization screen displays, press Control-S to configure the Intel Boot Agent (IBA) settings. On desktop adapters: Intel® Boot Agent (IBA) is enabled by default.
How do I fix Intel boot agent?
How to fix itPress F2 during boot to enter BIOS Setup.Go to Advanced > Boot > Boot Configuration.In the Boot Devices pane, disable Network Boot.Press F10 to exit BIOS Setup.
What is a boot agent?
The Boot Agent supports PXE and RPL in pre-boot, Windows, and DOS environments. In each of these environments, a single user interface allows you to configure the Boot Agent from a PXE and RPL BIOS on both Fast Ethernet and Gigabit adapters.
How do I turn off Realtek boot Agent?
How to Get Rid of a Realtek Boot Agent VirusOpen the Control Panel from the Start menu. ... Select "Add/Remove Programs."Select the "Realtek Boot Agent" in the list of applications that appears.Click "Change" or "Change/Remove" and select "Remove."Follow the on-screen instructions to fully uninstall the Boot Agent.More items...
How do I fix failure to boot?
Fixing “Disk boot failure” on WindowsRestart the computer.Open the BIOS. ... Go to the Boot tab.Change the order to position the hard disk as the 1st option. ... Save these settings.Restart the computer.
How do you exit boot Agent?
PXE-M0F: Exiting Intel Boot Agent....Check that the drive is detected in BIOS:Press F2 during boot to enter BIOS Setup.Go to the Boot menu.Check the Boot Drive Order.Press F10 to exit BIOS Setup.
What does initializing boot Agent mean?
That means it's trying to boot from the network card as there is a boot-over-lan thing that can be done. It usually comes up when the hard drive is dead or not present so it tries to like boot from floppy, usb, dvd, hard drive and then LAN. 0.
How do I update Intel boot agent?
For boot image update or installation using Intel PROSet for Windows* Device Manager:Open Windows* Device Manager.Select the network adapter to update.Select the Boot Options tab.Click the Flash information button.Click the Update Flash button.Read and respond to the caution prompt.More items...
How do I disable Ethernet boot agent?
Go to the property "Boot Order" and change the value to "ROM Disable". Then go to the property "Show Message Time" and set it to "1 Second". This is the minimum time the Ethernet Boot Agent will take. You can make the ethernet boot agent invisible by setting the property "Show Config Message" to "Disable".
Is Realtek a virus?
Realtek is a hardware company. You'll have to give us more information.
Are Realtek drivers safe?
If they are the correct "Windows 7" drivers that you need for the make and model of your computer AND you are either downloading these realtek drivers from Realtek's web site or your computer manufacture's web site then yes they are safe to download and update the realtek device drivers.
Is Realtek audio console a virus?
Realtek is not a virus, it is the most commonly used Audio driver setup on PC's these days, that also make software for other devices on your PC . . .
How do I update Intel boot agent?
For boot image update or installation using Intel PROSet for Windows* Device Manager:Open Windows* Device Manager.Select the network adapter to update.Select the Boot Options tab.Click the Flash information button.Click the Update Flash button.Read and respond to the caution prompt.More items...
What does initializing Intel boot agent mean?
That means it's trying to boot from the network card as there is a boot-over-lan thing that can be done. It usually comes up when the hard drive is dead or not present so it tries to like boot from floppy, usb, dvd, hard drive and then LAN.
How do I disable Ethernet boot agent?
Go to the property "Boot Order" and change the value to "ROM Disable". Then go to the property "Show Message Time" and set it to "1 Second". This is the minimum time the Ethernet Boot Agent will take. You can make the ethernet boot agent invisible by setting the property "Show Config Message" to "Disable".